1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
|
.help orfits Jan90 dataio
.ih
NAME
orfits -- convert FITS data files to IRAF image files
.ih
USAGE
orfits fits_file file_list iraf_file
.ih
PARAMETERS
.ls fits_file
The FITS data source. This is either a template describing a list of disk files
or a tape file
specification of the form mt*[n], where mt indicates a mag tape device,
* represents a density, and [n] is the tape file number.
If the tape file number n is specified then only that file
is converted. If the general tape device name is given, i.e. mta, mtb800, etc,
then the files specified by the file_list parameter will be read from the tape.
.le
.ls file_list
The files to be read from a tape are specified by the file_list string. The
string can consist of any sequence of file numbers separated by
at least one of comma, or dash.
A dash specifies a range of files. For example the string
"1,2,3-5,8-6"
will convert the files 1 through 8.
.le
.ls iraf_file
The IRAF file which will receive the FITS data if the make_image parameter
switch is set. Iraf_file can be a template of output image names or
a root output image name. In the former case one output image name
must be specified for every input file. In the latter case iraf_file is
a root output image name to which the input file sequence number or tape
file number is appended if the number of input files > 1. For example
reading files 1 and 3 from a FITS tape with a value of iraf_file of "data"
will produce the files data0001 and data0003, whereas reading the same
two files with a value of iraf_file of "data1,data2" will produce the files
data1 and data2.
.le
.ls make_image = yes
This switch determines whether FITS image data is converted to an IRAF image
file. This switch is set to no to obtain just header information with the
long_header or short_header switches.
.le
.ls long_header = no
If this switch is set the full FITS header is printed on the standard output.
.le
.ls short_header = yes
If this switch is set only the output filename,
the title string, and the image dimensions are printed.
.le
.ls datatype
The IRAF image file may be of a different data type than the FITS image data.
The data type may be specified as s for short, u for unsigned short,
i for integer, l for long,
r for real, and d for double. The user must beware of truncation problems if an
inappropriate data type is specified. If an incorrect data_type or a
null string is given for this parameter then a default data type is used
which is the appropriate minimum size for the input pixel values.
If the bscale and bzero parameters in the FITS header are undefined or equal to
1.0 and 0.0 respectively, orfits
selects datatype s or l depending on bitpix. If bscale and bzero are set to
other than 1.0 and 0.0, orfits selects datatype r.
.le
.ls blank = 0.
The IRAF image value of a blank pixel.
.le
.ls scale = yes
If scale equals no the integers are read directly off the tape.
Otherwise ORFITS checks the values of bscale and bzero. If these numbers
are not 1. and 0. respectively, ORFITS scales the data before output.
.le
.ls oldirafname = no
If the oldirafname switch is set ORFITS will attempt to restore the image to
disk with the filename defined by the IRAFNAME parameter in the FITS header.
.le
.ls offset = 0
Offset is an integer parameter specifying the offset to the current tape file
number. For example if offset = 100, iraf_file = "fits" and file_list = "1-3"
then the output file names will be "fits0101", "fits0102" and "fits0103"
respectively rather than "fits0001", "fits0002" and "fits0003".
.le
.ih
DESCRIPTION
FITS data is read from the specified source; either disk or
magnetic tape. The FITS header may optionally be printed on the standard
output as either a full listing or a short description.
The FITS long blocks option is supported.
At present non-standard FITS files (SIMPLE = F) and files containing
group data are skipped and a warning message is issued.
A warning message will be issued if the default user area allocated in
memory is too small
to hold all the FITS parameter cards being read in by ORFITS.
Since the default user area is 8000
characters and a single card image is 81 characters long, the normal
user area will hold 98 complete card images. ORFITS will not permit
partial cards to be written. The user can override the default user area
length by setting the environment variable min_lenuserarea (see example
below).
.ih
EXAMPLES
1. Convert a set of FITS files on tape to a set of IRAF image files, allowing
orfits to select the output datatype. Blanks are set to zero.
.nf
cl> orfits mtb1600 1-999 images
.fi
2. Convert a list of FITS files on disk to a set of IRAF images. In the first
case the files specified by fits* are written to the images images0001,
images0002, etc. In the second case the fits disk files listed one per
line in the text file fitslist are written to the output images listed
one per line in the file imlist.
.nf
cl> orfits fits* * images
cl. orfits @fitslist * @imlist
.fi
3. List the contents of a FITS tape on the standard output without creating
any image files.
.nf
cl> orfits mtb1600 1-999 images ma-
.fi
4. Convert FITS files directly to IRAF images without scaling.
.nf
cl> orfits mtb1600 1-999 images scal-
.fi
5. Convert the first three FITS files on tape to IRAF files setting blanks
to -1.
.nf
cl> orfits mta 1-3 images blan=-1
.fi
6. Read in a FITS file with a header roughly twice the usual IRAF length
of 8000 characters.
.nf
cl> set min_lenuserarea = 16300
cl> orfits mta 1 images
.fi
7. Read a FITS tape with 5 normal fits records (2880 bytes) to a tape record.
Notice that no extra parameters are needed.
.nf
cl> orfits mta 1-3 fits
.fi
.ih
BUGS
Blank pixels are counted and set to a user determined value, but not flagged
in the image header.
.ih
SEE ALSO
owfits, reblock, t2d
.endhelp
|
